/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$  Copyright (c)  $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
$            肖遥电子（广州）研发中心
$          Shawyoo Electronics (GuangZhou) R&D Center
$                        http://www.shawyoo.com   Email: autoele@qq.com
$         QQ群：9069471/9069433/9524253  All rights reserved.  
$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$  Copyright (c)  $$$$$$$$$$$$$$$$$$$$$$$$$$$ */
/* 
                                      文件描述
 文件名:
 功能描述：
 编译环境：
 目标CPU:
 作者：
 创建时间：
 建议编辑环境：UltraEdit 11.00a+  制表符宽度为三个字符，程序可读性更好。
$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
*/      
#ifndef  __UART0_H__
#define  __UART0_H__

#include    "RTOS.h"
#include  <string.h>
#include    "UserGlobals.h"

// $$$$$$$$$$$$$$$$$$ <<< Use Configuration Wizard in Context Menu >>> $$$$$$$$$$$$$$$$$
// <h>请选择是否使用UART，不使用则不占资源

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>USE_UART: 我要使用UART？ <0=> 不使用 <1=> 使用
//    <i> Default: 使用
*/
#define      USE_UART      0

// <h>UART0初始化相关配置(CPU主频在CPU.h文件中设置)
 

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>UART0_BPS: 串口波特率设置 <1-250000>
//    <i> Default: 9600
*/
#define      UART0_BPS      9600

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>U0_DATA_BIT: 数据位配置 <0=> 5位 <1=> 6位 <2=> 7位 <3=> 8位
//    <i> Default: 3
*/
#define      U0_DATA_BIT     3

// <e>禁止或使能校验位

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>U0_CHECK_BIT_EN: 校验位使能 <0=> 禁止校验 <1=> 允许校验
//    <i> Default: 1
*/
#define      U0_CHECK_BIT_EN  1

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>U0_CHECK_BIT: 校验位配置 <0=> 奇校验 <1=> 偶校验 <2=> 强制1 <3=> 强制0
//    <i> Default: 0
*/
#define      U0_CHECK_BIT     0

// </e>

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>U0_STOP_BIT: 停止位配置 <0=> 1位 <1=> 2位
//    <i> Default: 0
*/
#define      U0_STOP_BIT     0

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>U0_PROIRITY: 串口中断优先级 <0=> 不优先 <1=> 优先
//    <i> Default: 1
*/
#define      U0_PROIRITY     1

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>UART0_REC_LENGTH: 接收缓冲区长度字节设置 <1-1024>
//    <i> Default: 100
*/
#define  UART0_REC_LENGTH 150

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
//    <o>UART0_TXD_LENGTH: 发送缓冲区长度字节设置 <1-1024>
//    <i> Default: 100
*/
#define  UART0_TXD_LENGTH 1500

// </h>

// </h>

// $$$$$$$$$$$$$$$$$$$ <<< end of configuration section >>> $$$$$$$$$$$$$$$$$$$$$$$$$$$$

 

 

#ifdef      UART0_GLOBALS
#define     UART0_EXT
#else
#define     UART0_EXT    extern
#endif

#define    OWN_ADDRESS      1
#define    LEAD_OK          0x55
#define    LENGTH_OK        0xaa

#define  FIFO_LENGTH   14

#define  DATA_START_ADDR 6

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
    接收相关变量定义
*/
UART0_EXT struct
{
 uchar    Buffer[UART0_REC_LENGTH];  
 uchar  CheckSum,OverTime;
   uchar  Command,Error,Receiving;
   uint16   Counter,Length;
}  Rec;

/* $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
   
*/
UART0_EXT struct
{
   uchar   Buffer[UART0_TXD_LENGTH+12];
   uchar   CheckSum,Sending;  
   uint16  Length;
}  Txd;
UART0_EXT uchar      *TxdP;

uchar       PutString(uchar  *);
uchar       PutBuffer(uchar,uint16,uchar *);
void      Uart0_SendChar(uchar  data);
void   ClearReceiveFlag(uint16);
void   ClearTransmitFlag(void);

void      TaskUART0_ReceiveOK(void)   __task;

#endif

/*
 $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$  End of File $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
 */